News and Updates from Reverse Logic Limited...

Progressive Incline Race Ramps

Sun, 3 Jul 2011 16:04:26 -0400

Progressive Incline Race Ramps are designed specifically for cars with about 3” to 4” of ground clearance. The ramps feature a curved incline surface which increases from 4 degrees to 8 degrees to match the increasing angle of approach as a car climbs the ramps. This design results in a higher ramp platform for a given ramp length. Optional Trailer Ramp Adapters convert the RLL-89-2 incline sections to Race Ramps Trailer Ramps. More details here.

Tailer Ramp Adapters

Sun, 6 Mar 2011 09:19:21 -0500

Trailer Ramp Adapters convert the incline section of the RLL-87-2 ramps into Trailer Ramps. This solution is less expensive than purchasing dedicated Trailer Ramps and requires less space to store and transport.

The resulting trailer ramp is 68” long by 8.5” high with an initial incline approach of 6.8 degrees. Learn more about the RLL-87-2 two-piece, two-stage incline ramps and trailer ramp adapters here.

Buyers Products WC1467A Wheel Chocks

Sun, 30 Jan 2011 20:51:16 -0500

We have wanted to offer the Buyers Products WC1467A Wheel Chocks since we started selling Race Ramps service ramps a year ago. But, the three pound shipping weight for these heavy duty reinforced rubber wheel chocks made it difficult to deliver them at a reasonable price. That changed when the Post Office began offering Regional Rate shipping for small heavy packages beginning in January 2011.

The WC1467A Wheel Chock is a perfect complement to the Race Ramps service ramps we sell, especially the two piece ramps with a removable incline section. In fact, a solid wheel chock is a good companion for our entire product line of jack pad tools, lug bolt guide tools, and Race Ramps.

Our delivered prices for the Wheel Chocks are $15 for one, $27 for two and, $48 for a set of four. A small price to pay for the peace of mind they offer.

Two Stage Incline Race Ramps

Tue, 25 Jan 2011 08:43:53 -0500

For some cars with very low ground clearance, the 10.75 degree incline of the standard RR-56 or RR-XT (67”) Race Ramps is still too steep. Reverse Logic Limited requested Brute Industries to manufacture a modified ramp design which incorporates a 2-stage incline into the ramp section. Reverse Logic Limited is now accepting orders for the new ramps.

Two models of the 2-Piece, 2-Stage Incline Race Ramps are available. The RLL-87-2 ramps are 10” high by 14” wide with an overall length of 87”. The RLL-72-2 ramps are 8” high by 12” wide with an overall length of 72”.

You only need 3.5” of ground clearance 24” in front of your front tire foot print in order to use the new ramps. More details including pricing here.

StarFest 2010 September 24-29

Thu, 6 May 2010 09:40:03 -0400

Reverse Logic Limited is a sponsor for the MBCA StarFest 2010 track event in September. The driving events will take place at Summit Point Motorsports Park in WV. We will be participating in the track events and bringing as many door prizes as we can fit in the trunk. Event details and Hotel information can be found at www.StarFest2010.com. Registration is open in June. Let us know if you plan to attend and we will make a special point to introduce ourselves in September.

Stainless Steel Lug Bolt Guide Tools

Mon, 26 Apr 2010 07:28:15 -0400

Reverse Logic Limited now offers two grades of lug bolt guide tools (also called Wheel Hangers). The stainless steel professional series are heavy duty tools which can stand up to the rigors of daily use. The stainless steel version of the tools are significantly stronger than the aluminum tools. The added strength is especially useful for lug-centered aftermarket wheels where the full weight of the wheel and tire are supported by the lug bolt guide tool until the lug bolts are installed.

The M12x1.5 and M14x1.5 stainless steel lug bolt guide tools are available for $15.95 including shipping. The heavy duty M14x1.25 lug bolt guide tool is not currently available.

Trak-Jax and Flatstoppers now available from Reverse Logic Limited

Fri, 22 Jan 2010 21:20:06 -0500

Constructed with space shuttle foam technology, Race Ramps are made with one solid piece of high-density polystyrene and a hybrid polyurea coating. They are practically indestructible while also being extremely lightweight. A pair of 30 inch ramps can hold up to 3,000 pounds while weighing only 5 pounds per ramp. Specially made for use with wide tires and/or low ground clearance cars, the Trak-Jax (with 7.8 degree incline) will raise a car up three inches which is high enough to fit a floor jack under the car.

Because of their unique construction, Race Ramp products will not slide across a garage floor, dig into an asphalt driveway, or scratch or otherwise damage a cement or painted floor. They can be used on almost any flat surface, plus they will never rust. The larger products come complete with straps for easy carrying and storage. Race Ramp products are lightweight, durable, and handmade in the USA.

Reverse Logic only ships Race Ramps products to the 48 Continental United States.

X204 Jack Pad Tool Now Available for MB GLK

Sun, 22 Nov 2009 13:17:23 -0500

Just about every MB chassis introduced since 2001 incorporates integrated vehicle jack pockets in the jack points mounted just behind the front wheels and just forward of the rear wheels. Until the introduction of the 2010 GLK SUV, all of the jack points with the vehicle jack pocket had a notch in either end of the pocket. Our jack pad tools utilize this notch as a means to suspend the tool from the jack point.

The dimensions of the pocket in the GLK jack point are roughly the same as the pocket in the jack points of the other Mercedes-Benz models which we support. But, the spring loaded pins used in our other MB jack pad tools are of no use with the GLK jack point.

Fortunately, the silicone plugs which are used in our BMW and Nissan GT-R tools work well with the GLK jack point. The block on the jack pad tool for the GLK is the same as our other MB jack pad tools. Combined with the plugs from our BMW tools, we are able to offer a chassis specific jack pad tool for the GLK.

Jack Pad Tool for Nissan GT-R

Fri, 13 Nov 2009 13:06:18 -0500

The jack points on a Nissan GT-R are much larger than those used on BMWs. However, the pocket in the jack point of the GT-R is very similar in size to the pockets in a typical BMW jack point.

In June 2009 we began offering a hand-crafted Jack Pad Tool for the Nissan GT-R in limited quantities. Sales volume has increased to the point where we now make the jack pad tool block, which is unique to the GT-R, on a CNC milling machine. This tool shares the base with our tools for BMW and MB.

Like our BMW jack pad tools, the GT-R tool uses silicone plugs to hold the jack pad tool in place while a floor jack or four-arm lift is maneuvered into place.

Three Lug Bolt Guide Tools for European Cars

Fri, 13 Nov 2009 00:11:19 -0500

Most of the do-it-yourselfers using our Jack Pad Tools are doing so in order to remove or install the wheels on their Mercedes-Benz and BMW cars. European cars use lug bolts instead of lug nuts typically found on American and Japanese cars. Our anodized aluminum Lug Bolt Guide Tools (also called Wheel Hangers) simplify the installation and removal of wheels by aligning the holes in the wheel with the threaded holes in the wheel hub.

While there are several other suppliers of Lug Bolt Guide Tools, none of our competitors offer a better value than our tools. At $9.95 including shipping to anywhere in the USA or Canada, it is difficult to beat our value proposition for the M12x1.5 and M14x1.5 anodized aluminum Lug Bolt Guide Tools.

The M12x1.5 and M14x1.5 tools will fit most European cars including BMW, Mercedes-Benz, Audi, Porsche, VW, and Saab. A third tool with an M14x1.25 thread size fits MINI Cooper R50/R52/R53 (from July 2006), MINI Cooper R55/R56/R57, and BMW E70/E71/F01/F02 chassis.

In 2010 we plan to introduce stainless steel versions of the lug bolt guide tools. If you are interested in these, send us an e-mail and we will notify you when they become available. The M12x1.5 size is the first tool we will offer in stainless steel (Q1 2010).